Press "Enter" to skip to content

How do you get stains out of marble fireplace?

Tips for cleaning a marble fireplace or surround

  1. Use a soft microfibre cloth to remove surface dust and dirt.
  2. Use warm (not hot) water.
  3. Lightly rub the stain with the cloth, increasing in pressure if the stain is stubborn.
  4. Regularly rinse the cloth out to keep it clean.

How do you get a stain out of marble?

For most organic food stains, the Marble Institute recommends cleaning with a solution of 12% hydrogen peroxide and a few drops of ammonia; if you spilled anything oil-based, like a vinaigrette, and the stain has set, attack it (gently) with a liquid cleanser that contains “household detergent, mineral spirits, or …

Does baking soda ruin marble?

Baking soda is alkaline so you should only use it with caution. It is also a mild abrasive, so you need to use it gently rather than applying elbow grease. Because of these factors, a baking soda cleanser should not be used on marble every day. Frequent use could dull your marble countertop.

How do you get yellow stains out of marble?

Mix a few drops of ammonia with 12% hydrogen peroxide to spot clean the stained area. However, be careful when using this method on darker stones as the hydrogen peroxide can lighten the color of the marble. To successfully remove stains from marble, you need to draw them out of the delicate surfaces.

Can you use magic eraser on marble?

Magic Erasers are abrasive, so avoid using them on delicate countertops such as marble and granite. Not only can you damage the sealant but the eraser may make the countertop appear dull.

How do you fix discolored marble?

A homemade paste of baking soda and acetone can do the trick too; let this sit on the stain for about 24 hours and clean as usual. Remember to avoid cleaners with acidic ingredients. Never use abrasive sponges or cleaning tools on your marble tabletop.

How do I get my marble white again?

Mix three tablespoons (44ml) of baking soda with one quart (946ml) of water. Use a shammy to spread this mixture over your marble surface. Let the mixture sit on your marble for a few hours before wiping it away with a wet cloth.

Is hydrogen peroxide safe for marble?

Do not use common cleaners like bleach, vinegar, hydrogen peroxide, and ammonia since these will etch marble (travertine and limestone too) leaving dull spots, rings, or spray marks. Etching is a chemical burn to the marble surface which requires re-polishing. Avoid acidic & citrus cleaners.

Can you use Bar Keepers Friend on marble?

Bar Keepers Friend Granite & Stone Cleaner & Polish is specially formulated for use on smooth, polished stone, including granite, marble, and quartz. Its pH-balanced formula won’t scratch or mar stone finishes, and it’s gentle enough to use every day.

How do you prevent water stains on marble?

Water Stain Prevention The key to preventing water spots and stains on your marble countertops is to perform regular marble cleaning and keep the surface area dry. Absorb water spills with a paper towel as soon as you notice them, and wipe down the surface area with a soft cloth.

How do you remove deep etching from marble?

Steps to Remove your Etch Mark

  1. Wipe the surface Clean. Above the Etch Mark, wipe the surface clean of any grit of dirt.
  2. Cover the Etch Mark with Polishing Powder. Add MB 11 Polishing Powder.
  3. Add water to polishing powder.
  4. Dampen the Towel, and Begin scrubbing the Stain.
  5. Clean up using a marble cleaner.

How do you revive dull marble?

Another traditional method to restore the gleam of marble countertops is to polish them with baking soda. Mix three tablespoons of soda with one quart of water and apply it on the surface, then let air dry for several hours.

How do you remove etch marks from honed marble?

Sprinkle a scrubbing cleanser onto the surface with a few drops of water. Take a scouring pad, and move in a circular motion to hone the material. After just a few minutes, the surface will dry and you will see a restored material.

What does etching look like on honed marble?

Etch marks are misinterpreted as “water marks” Since the acid removes part of the marble surface, the newly exposed surface is not polished. Compared to its surrounds this makes the etch mark look like a dull white mark. A lot of times this will occur as a ring around a glass/cup that leaked an acidic liquid.

How do you remove water stains from honed marble?

Here are a few things you can try for removing hard water spots: Use a gentle detergent with water. Scrub lightly with a soft bristled brush. If the buildup requires a little more elbow grease, gently buff the surface with a piece of dry super-fine grade (0000) steel wool.